Archive

Monthly Archives: July 2017
12

Best Tool Bags For Electricians: How To Be Prepared For Anything

Everything you need to know about the best tool bag for electricians is here! Read up and save the questions. I hope this list helps! If you have any queries, feel free to comment. Happy tool bag hunting!

More…

Introduction

Shopping for bags isn’t only a woman’s thing. If your profession involves handling a set of tools or handy equipment, choosing a bag is crucial. It can make or break your work habits, and it may or may not help you save effort and observe safety.

So what do you need to know about choosing the best tool bag for electricians?

best tool bag for electricians

Tool Bags and What They Should Be

Tool bags, just like any other kind of bags, come in different sizes, shapes, material, and functionality. Depending on your need for an electrician, you need to pick carefully among these factors. Let us go through each of them to know the points you need to consider.

Cost of Tool Bags

Today, tool bags can range from as cheap as $15 to around $80. The cheapest in this range is an essential instrument bag that is small but very portable. On the other hand, the pricier ones are the heavy-duty ones that are used in large-scale handyman work.

A lot of handymen think they should not be spending too much money on it. However, sacrificing the quality of the tool bag just to save money may not be the wisest decision.

If you are going to use it for a living, you better invest in a high-quality bag. Purchase something you can use and can last several years. You would not want to keep on changing and buying new ones every time.

Space-saving Quality of Tool Bags

This should be one of our priorities for many reasons. One, you will never know when you will need to add more tools as you find better brands and functions. In this case, you will need a spare space.

Also, it’s important that you don’t carry your tool bags with the tools overflowing as it may not be safe. You don’t just pack everything in too because you wouldn’t want to ruin the bag itself.

It also helps to have a bag that has several pockets inside and out. This space-saving quality will save you when you need to store super small accessories that are easily lost. You no longer have to worry when you’re working up on the electric post, and you need to a screw.

Type of Tool Bags

Now, this concerns two things: the functionality or convenience of the bag and your taste. I know these two do not always go along. That may even be the reason why you have reached this article looking for the right bag, right?

You have to know the type that would go best with your body type and condition. That is a primary consideration. If you are the type to have a backpack, go for it. But if your back is too tired and you couldn’t afford to strain it, then go for a belt bag.

A sling bag could be nice if you are a natural light packer. A handbag could be a good one too, but only if you are not prone to losing valuables. If you are buying at a physical store, check the mirror too. Find out what works best and fits your preferred look.

The manufacturer

Now, this may sound very meticulous, but it helps. It contributes to knowing the manufacturing company that makes it because good reputation means good product.

Some people even think it matters where the bag is made. Most USA-made bags are known to be durable, but most China-made bags are cheaper. So again, it is a battle of the quality and the cost.

Each brand also has their signature feature that you should be on the lookout for. Each one sports a good number of compartments and pockets, and of course, unique designs.

Features

Of course, this matters the most. It is really up to you to figure out which features fit your needs. You can go for a bag that has a humongous number of pockets but still finds it not useful.

Features-Tool-Bags-for-Electricians

The standard features for you to take note are the material, the stitches and weave placements, the thickness and thinness. Then you also have to check the straps, the padding, the width and depth of the pockets.

The tools that you already have are the biggest factors here. If it is possible for you to bring them while you shop for your tool bag, then go for it.

It is not just a matter of which bag has the newest features. It will still and always be the durability and how long it can last. These two are the most important factors to consider if you are a professional electrician.

For other tips, notes and reminders as to what bags to choose, check out Joseshome.com.

Top 5 Best Tool Bag for Electricians

1. Crazy Ants Reel

Key Features: This organizer contains a total of 25 pockets. It can be easily rolled and buckled for carrying and easy storage. The length of the bag extends to 27.1 inches, and the width of 13.8 inches.

Via Amazon.comCheck Price & Review on Amazon

Pros

  • It is perfect for when the handyman or electrician is always on the go or needs to hurry up. It is easy to pack up and carry.
  • The straps are clip-on, so you won’t have to worry about locks on the loose.
  • The pockets are wide enough to fit wide tools.
  • The pockets have covers to secure tiny accessories like screws.
  • It can easily be stored and is space-saving since it can be rolled and easily strapped.
  • It can hold several flat tools at the same time.
  • The insides of the bag are padded with rubber. This helps protect the tools from wearing in case of rain or too much heat.
  • It is good quality for the cost as it is basic but very functional.

Cons

  • The bag is a little too thin, even when it is already rolled up and locked.
  • The bag may only be convenient for packing and holding flat tools. Super round and edged tools may be too bulky to put in and might tear the pockets easily.

2. Custom Leather Craft 1528

Via Amazon.com

Check Price & Review on Amazon

Key Features: This tool carrier and organizer is a box-type organizer that helps prevent the tools from falling off.  It contains a total of 21 pockets—14 on the outside, and seven on the inside. The package includes plastic trays that can hold other accessories and slide at the sides and bottom of the bag.

Pros

  • This bag is made out of leather. It is durable and cannot easily be worn and torn even by the size of the tools.
  • The handle of the bag is double padded to make sure the bag does not fall off. You won’t have to worry about the weight of what’s inside.
  • You can convert this bag from a handbag to a shoulder bag with its extra strap.
  • The plastic trays come in handy for small parts. They can be conveniently placed at the bottom inside or at the side pockets.
  • You can easily cram on packing the tools when you are in a hurry or on the go. The pockets are wide enough for you to do that.

Cons

  • There are no loops available for when you need to store nut drivers.
  • Some of the pockets are too deep, and you cannot reach with your hands. You will end up just storing the long tools like pliers.
  • Even with its leather coat, the pockets may sag quickly especially when you use it every day. That may not be convenient if you need to go up a roof or a post.

3. McGuire-Nicholas 526-CC

Via Amazon.com

Check Price & Review on Amazon

Key Features: This pouch has a professional-looking bag made of leather matches the shapes and size of most essential tools. It has a tape clip chain shaped like a letter T to secure its hold. It is guaranteed durable with its hard and thick material and texture.

Pros

  • This pouch has holders and pockets that are specially made for the basic electrician tools like flashlights. It even has a holder for keys and tape measure.
  • It can hold all tools and make it possible for the electrician not to feel all bulky.
  • Since it does not feel super heavy unlike other pouches, it does not strain the back.
  • You can store a set of pliers, dykes, tin snips, voltage tester, utility knife and even markers.
  • It has wide spaces, so you will not have to worry about the tools overlapping or hitting one another.
  • Because it is made with durable material, it can last long—around six months as a minimum.
  • The stitches are well placed and are solid, especially for the pockets.
  • For the kind of leather used, it is a whole lot cheaper than other electrician tool bags.

Cons

  • Because of its material, it feels a little hard at first. You still have to rub it with oil and use it frequently before it could feel “normal.”
  • It has a slightly thin belt which may snap quickly through time. You will then have to replace it with a much thicker belt.

4. Snap-On 870110 20-Inch Wide Mouth Tool Bag

Main Features: This tool bag created by Snap-on is made out of polyester that is water-resistant. It highlights its wide mouth feature that makes putting in big tools easier for the user. It contains a total of 20 pockets for both inside and outside.

Via Amazon.com

Check Price & Review on Amazon

Pros

  • This item is a shoulder-type tool bag and is meant for carrying and traveling. You do not just strap it to your waist but keep everything in and secure them.
  • The shoulder strap that comes with it is adjustable and is padded. You will not have to worry about straining your shoulder blades when you need to carry the bag for long hours.
  • The bag is extensive (20 inches), so you can fit in all the big basic tools like hammer, screwdriver, and pliers.
  • The stitches are robust and placed correctly. That means the material is not that prone to easy wear and tear.
  • Because it is made with durable material, it can last long—even up to years!
  • It has an extra protector material at the bottom that can secure your tools even when they are heavy. The polyester will not get easily scratched or torn.
  • It has an ID and badge windows where you can place your ID’s or cards correctly.

Cons

  • The pockets are a little too shallow so it may not hold very long tools. They may not be ideal for keeping small accessories like keys too.
  • It is a little hard to balance the items inside while you are carrying it. The weight of the tools does not evenly distribute. That may not be ideal for when you are up a roof or a post.
  • It may not be too convenient for when you can only use one hand to get the tools inside.

5. Klein Tools 554171814 Tradesman Pro Organizer Extreme Electrician’s Bag

Via Amazon.com

Check Price & Review on Amazon

Main Features: This bag is designed for professional use as it contains a total of 78 pockets. It has padding at the bottom which helps hold heavy tools securely. It is stitched and weaved (1680D) for extra durability.

Pros

  • This bag can hold several tools simultaneously with the whopping 78 pockets. That is a number that overthrows other tool bags.
  • It is 10 inches deep so that you can store tools vertically.
  • The bottom of the bag is fully padded and molded to make sure it does not rip off. That is perfect for when you need to store hammers and other drivers.
  • The bag has bars that serve as locks so that even when you leave the bag, it does not prop open.
  • The bag is overall well constructed and well designed for a professional electrician’s use.
  • You can fit up to 20 pounds of tools in it and not get it ripped off. That means the bag can last up to years of proper use.
  • It has wheels at the bottom so that you can transport the bag more quickly.

Cons

  • Because of the lock bars, it may be tough to bring the tools out of the bag. You will have to open the bag with one hand and retrieve the tools with the other.
  • The zippers may not that be stitched well so overusing it can cause the zipping mechanism to break.

Conclusion

So there you have it! Those are the top 5 best tool bags for electricians. If you were to ask me, I’d say you should go for the McGuire-Nicholas 526-CC Brown Professional Electrician’S Pouch.

I choose this particularly because the pros outweigh all the cons listed. And apparently, the cons are things you can quickly adjust to. Also, it is designed to fit the needs of a professional electrician, so it still appears to be the best.

2

How to Make a Deer Feeder: The Best Do It Yourself Tricks

Are you an active wildlife enthusiast? When was the last time you hunted for or took care of a wildlife deer? What equipment do you have that aid you in this activity?

Whether you’re a professional hunter or just someone on a lookout for a new hobby, you will need good gears. Using the right tools is crucial, especially if you are hunting. The thing is, though, having an excellent set of equipment usually requires spending a lot of money.

More…

Now if you are doing this one time or are just at the beginning of your wildlife journey, there is an alternative. Let’s talk about going for a DIY or do-it-yourself.

This article will teach you the basics of how to make a deer feeder—homemade that is. Hopefully, this will cost you less money and will still make the job easier to do.

What You Will Need​

What-You-Will-Need​-How-to-Make-a-Deer-Feeder

As you may already know, the goal of a deer feeder is to just supply food to the animal in the most convenient way possible. The mechanism is expected not to give the deer a hard time. This is the reason why most forest rangers and hunters prefer automatic deer feeders.

But like I said, since it costs a lot of money to purchase the automatic feeder, we are listing down all the things we need to build our own. Since there are a lot of different materials to choose from, we narrowed it down to two.

1. A PVC pipe

The idea is to tie the pipe tightly to a sturdy tree to help gravity do its job. The food will just go all the way down from the top hole to the bottom hole. You may use any size of PVC pipe depending on the size of tree you will be tying it on.

An acceptable minimum size would be a 4-inch. As for the length, you will also have to decide as you estimate the deer’s size.​

​2. A grate and a plug

These tools will help secure the pipe tightly to tree or fence. These will also keep the holes sealed. Specifically, the grate’s job is to drain all possible liquids that might get into the pipe, like rain. This way the foods will not easily spoil.

​3. Ropes

Obviously, this is what you use to tie the pipes. You will need to know the basic sturdy knots to make sure they are placed and locked. You need to make sure you tie it to the tree closest to your viewing range if you are hunting.​

Ropes

4. Buckets or barrels

This is another type of feeding tool you can use in exchange for pipes. This will be more convenient if you are not up for the technicalities of the DIY pipe feeders. You only need a standard-sized bucket that is wide enough for the deer to bow down too.

One advantage of using a bucket is that you will not be wasting a lot of food. The deer get to pace its feeding in it too.​

5. Big plastic buckets​

If you think placing the standard-sized buckets on the ground is too low for it to reach, you may still tie it. Perhaps you can build your fences to try on the pail. Even a 5-gallon pail or container will do.

For other tools that can be used as alternatives, check out these other projects from​ https://joseshome.com/

How to Make a Deer Feeder​

How to Make a Deer Feeder

The following procedures vary as there are different types of feeders you can do. To start off, let’s list down the ones for PVC feeders.

1. Cut or saw the PVC’s. Put the top and bottom together.​

Your desired length must be observed in the cutting or sawing. The length of the pipe where the food will roll down must not be too thin or too thick for the eye at the bottom part. And then, assemble by putting the two together.

2. Place the grate at the bottom and the plug at the top.

As mentioned earlier, these two will help secure the food inside and prevent it from being wet. Make sure both “lids” are tight enough so that even the slightest drop of water does not come through.​

​3. Get the 5-galon bucket and drill holes at the bottom.

These holes must be of the same size. These will be where your broom handle will pass through later on. After drilling, screw two nails at the opposite ends of the broom handle.

4. Insert the broom handle.​

Insert it inside the bucket, passing through the drilled hole. Slide it in place carefully so as not to widen the holes too much.

5. Tie the ropes.​

Do this with one end on the bucket and one on the part of the tree where you are placing the feeder. This will enable the feeder to hang around. Lower down the height between the bucket and the ground to your preference—around 4-5 feet.

Conclusion

There you have it! A quick DIY list of how to make a deer feeder in the comfort of your home. All the tools you will need for these projects are readily available in your local hardware, so you have no excuse.

Now you do not have to worry about where to get good automatic feeders for your hunting game. This is cost-efficient and can also enhance your mechanical creativity. Happy wildlife hunting!​

Make-a-Deer-Feeder-The-Best-DIY-Tricks

34

Things to Look Out for When Finding the Best Table Saw Under $1000

Table saws have a lot of uses and can be a really useful equipment to have at home. You can attach much more saw blades and accessories to work different purposes. If you know how to make the most out of it. And of course, if you have the best table saw under $1000 for your projects.

More…

However, to make this possible, there are several things you must look out for first before buying your table saw. Aside from the price, the size of your workplace and durability among all others, here are some more factors to consider.

Explaining the Table Saw

Before the table saw was invented, many carpenters used a simple hacksaw to cut wood. They simply took a plank of wood and clamped it to a hard surface, sometimes even using their foot for clamping.

Nowadays, technology has evolved to meet the growing demands of efficiency for carpentry. Although you can still cut wood traditionally, there are a lot of faster ways such as using a table saw.

Explaining the Table Saw

Table saws are high-powered blades that are built in a working table. These saws are circular blades that almost resembles that of meat saw in a butcher shop. The point of using a table saw is to cut cleaner, faster, and more wood.

Although a table saw can be easily imagined as a table top with a saw in the middle, it’s not a walk in the park to use. Unlike a stationary hacksaw, the table saw, once in motion, is a highly dangerous equipment. Thus, research carefully on how to use it.

Although it has a reputation for being a scary equipment, which is further worsened by Hollywood, every aspiring artisan should try using it. It’ll save you hours of sawing wood, and it can make your projects look professional with ease.

Advantages with a Table Saw

The table saw has a lot of benefits, and the first thing that comes to your mind is that it’s perfect for businesses. Even though you’re not exactly running a factory, it’ll still be a worthy investment.

For example, say you’re running a wood shop, then you can quickly benefit from this because the time in cutting wood will be as quick as a few seconds.

Time efficient

Time efficient

Thanks to the saw’s incredible power and overall design, it swiftly cuts through wood without any problem. The best thing here is that there are a few nifty tricks that you can use to cut blocks of wood at the same time.

Dual purposeThe table saw doesn’t only saw wood. If it’s not being used, then it’ll still be useful because of the wide surface of the table. You can do many things with the table saw’s top. An example would be measuring your wood works or even using it to nail wood joints.

Minimal work required

using-a-table-saw-can-save-you-the-effort-of-polishing-the-wood

Besides reducing the cutting work, using a table saw can save you the effort of polishing the wood. If you’re using a hacksaw, there will be a lot of rough sawdust and wood shavings present on the surface of the newly cut wood.

This is the result of the hacksaw’s grinding teeth along with the inconsistent pressure from your hands. Since the table saw has a consistent motor and an extremely sharp blade, you’ll have a cleaner cut that doesn’t need sanding.

Tips and Tricks When Using a Table Saw

Tips-and-Tricks-When-Using-a-Table-Saw

Here are some tips that you can further look into when using a table saw:

  • Know the cut you’re doing – This is the first and simplest step. There are two cuts. These are the rip cut and the cross cut. The rip cut goes along with the grain of the wood, while the cross cut cuts through the grain.
  • Always use a square before cutting – Alignment is essential when getting the best cuts through a table saw. Hence, always use a square to check if the wood is aligned with the saw. There are other things to check, such as the alignment of the fence to the wood, the blade’s alignment to the table, and the alignment of the blade guard.
  • Use a push stick – A push stick or a drive board is probably the most important tip. This pushes the wood towards the blade while distancing your hand away from the blade. It’s a must if you’re looking to play it safe, which you always should.
  • Cut flat wood – The table saw isn’t the best at cutting irregular shapes and spheres. Hence, always use your table saw for flat wood only. It’s typically best when you’re at the beginning of your project, not when you’re trimming wood sculptures.
  • Use a clamp with a miter gauge for faster work – If you’re looking to do cross cuts for a lot of timber boards, using a clamp is key. Attach the C-clamp to the miter gauge and clamp the wood boards together. Afterward, only run it through the blade.

Some More Things To Look Out For

1. Types of table saw

There are three main types of table saw: cabinet saw, the contractor saw, and the hybrid saw. The cabinet saw would be the biggest and the heaviest type of table saw among the three categories. It also very, if not the most, expensive type of table saw.

A cabinet saw’s motor range is usually between the 3HP to the 5HP range. The motor is located underneath the saw table, enclosed with a cabinet. The contractors saw on the other hand, significantly lighter than the cabinet saw.It is designed to be easily portable for contractors who need to bring the equipment to construction sites, just as the name suggests. Unlike the cabinet saw which happens to be made mostly of cast iron, the contractor is made from aluminum.

What the motor of a contractor table saw is mounted outside, and the blade is belt-driven. Its engine power usually ranges from 1HP to ¾ HP. And lastly, is the hybrid saw. A hybrid table saw is a hybrid combination of the first two types.

However, the material of the hybrid table saw, its other features and gears among all others might slightly differ, depending on the manufacturer and the brand.

2. Dust collection

Its dust collection is also another important function and feature. Using a table saw on any project would produce a lot of wood shavings. It is essential that your table saw has a good dust collection system.

There are a lot of table saws out there that come with a dust cabinet or some “capture system” to funnel out any dust wood shavings accumulated during the project.

3. Safety Features

some-safety-features-in-their-table-saws

This is one of the most important factors to consider. Especially to those who are not professional users of a table saw. There are a lot of brands out there that offer some safety features in their table saws such as a paddle style switch, anti-kickback pawls, riving knife, blade guards and blade breaks.

So do not be afraid to ask the salesperson which safety features do the table saw you’re planning to buy have.

Although these might not be all of the factors you must consider, these are some of the basics covered. But then again, no particular feature beats a good maintenance in prolonging the lifespan of your table saw.

Our Top 5 Picks

​#1 DEWALT DW745

The DW745 starts at a low price. It comes with one 24-tooth saw blade, but if you want an extra blade combo, you can buy the whole set for $330.78. In addition, it weighs 53 lbs and boasts accurate cutting, ideal for large home projects and professionals.

Check The Lastest Price on Amazon!

Via Amazon.com

It includes a steel roll cage, rack and pinion fence system, Mitre fence, two blade spanners, parallel fence, push stick, and a dust port reducer for easy cleanup. Comes with a 3-year warranty, one year of service, and a 90-day guarantee.

PROS CON
  • It has many accuracy features
  • Get straight and accurate measurements when cutting.
  • It provides hands-free use.
  • No need to put your hand on the handle to keep it steady since it is already a sturdy table saw.
  • It has a large rip capacity of 20”.
  • It does not come with a saw stand.
  • Despite the price, the stands are sold separately.
  • Its large shape makes it difficult to carry around.

#2 SKIL 3410-02

The 3410-02 is priced similarly to the DEWALT and comes with both a table saw and a folding stand. The table measures 20” x 26” but can stretch up to 20” x 36”. The stand is made of heavy-duty steel and provides easy and fast setup for projects around the house.

Check The Lastest Price on Amazon!

Via Amazon.com

It has a maximum cut depth of up to 3.5in, depending on the material being cut, and has a self-aligning rip fence for accurate measurement and cutting. It also has a three-year warranty and a 30-day Money Back Guarantee.

PROS CON
  • Very portable and easy to use.
  • Weighs 67 lbs and stands at 28.9” with the stand.
  • It has a self-aligning fence for more accurate cuts.
  • Has an EZ view measurement system for accurate settings.
  • It does not come with a saw stan
  • It has no dust collection port.
  • Provided saw blade is ideal only for small wood projects.○ You need to buy separate blades for bigger projectsd.

#3 Craftsman Evolv

The Craftsman is at the lower end of table saws, suitable for the DIY home projects. The sheer 25” x 17” die cast aluminum table offers support for significant materials, with a maximum cut depth of 3”, promoted by a durable steel stand at the height of 36”.

Check The Lastest Price on Amazon!

Via Amazon.com

You’ll be getting a table saw, stand, blade wrenches, 24T blade, hex keys, blade guard assembly, push stick, miter gauge, and rip fence, as well as a one-year general warranty. Some assembly is required, however.

PROS CON
  • It is light and portable.
  • It is easy to setup and assemble, and is light enough to carry around the house.
  • Its miter gauge gives you quick, accurate control.
  • It uses an AC Power source.
  • It does not have a dust collection port.
  • Its blade included not suitable for strong metal plates.
  • Not strong enough for commercial use.

#4 Bosch 4100-09

The 4100-09 is known to be one of the most expensive in this list but is worth the many features it offers. Its gravity-rise wheels make it roll around with ease. Its 29” x 21.5” tabletop has a 25” rip capacity and a saw blade, which is easily and quickly changeable.

Check The Lastest Price on Amazon!

Via Amazon.com

The 4100-09 offers a 1-year manufacturer warranty and a 30-day money back guarantee. The set includes a Gravity-Rise Table Stand; a 40-tooth carbide tipped saw blade, a miter gauge, push stick, and both a blade and hex adjustment wrench. Ideal for home and commercial use.

PROS CON
  • It has an innovative gravity-rise wheel stand.
  • This makes it easy to move around and setup for use.
  • Has multiple safety features
  • It has Bosch’s Smart Guard and Squarelock rip fence for maximum protection.
  • Is very heavy duty.
  • It can be used for larger construction projects.
  • It weighs 124.2 pounds
  • Hard to carry in places where wheels are incapable of passing on like stairs.
  • It is compatible with other blades, but only provides one type of blade.

#5 Rockwell Blade

Runner X2The Bladerunner X2 is one of the most affordable tables saw on this list. It uses a jigsaw blade instead of a circular blade and is perfect for those doing small and low-budget projects with necessary hardware materials.

Check The Lastest Price on Amazon!

Via Amazon.com

Its feature includes a large steel rip fence, a miter gauge, a 5-piece starter blade set, and a vacuum port for easy cleanup. The Bladerunner provides a compartment for your blades. Rockwell also offers a manufacturer’s three-year warranty.

PROS CON
  • It is compatible with any 4” T-shank jigsaw blade
  • Use any blade replacement, regardless of brand.
  • It is portable.
  • It is lightweight at 15lbs and has a table top handle.
  • Blade changes are tool-free.
  • Offers hands-free operation so you can focus on precise cuts.
  • Not recommended for a larger project that requires higher accuracy.
  • It does not come with a stand and needs a sturdy workbench.
  • It supposedly wobbles and often vibrates when in use.

The Verdict

For table saws under $1000, expect smaller, portable models more appropriate for small projects at home than ones you can use commercially for purposes like construction.

The Bosch 4100-09 is the choice if you’re looking for the closest to budget heavy-duty commercial models, while the Dewalt DW745 if you already have a spare table saw stand or sturdy workbench at home.

But if you want an all-around table saw at a budget, the SKIL 3410-02 is the best table saw under $1000. It has its stand and has self-aligning features. While its blade is lacking, this is easily fixed by purchasing other modules in your local hardware store.

Whichever you choose, always remember to practice safety and be aware of how to properly operate sharp cutting tools before using them. Read up on your table saw’s manual and avoid attempting to use it beyond its prescribed usage and limits.