Archive

Category Archives for "HOME TIPS & TRICKS"

10 simple painting tricks for the perfect home interior

Right in this article are 10 simple painting tricks for the perfect home interior, follow them to have a smooth project. These tricks would help you to cut down the cleanup time by half and substantially extend the paint job lifespan. However, there is no need to strictly obey the information down below though, feel free to incorporate adjustment if needed.

 

  • 1/ Clean and prepare the panting surface   

 

In order for the paint to adhere properly, you must clean the painting surface and remove dirt, mildew, grime, etc. You could use a power sprayer to perform the task but a stiff-bristle brush should be just as effective. Fill any hole and crack you can find with putty, wait for the material to cure then sand it flush.

 

Usually, you should be able to paint over an already painted surface if the old paint is in good condition. But if the old paint has flaked off or blistered in several spots, you have to scrape them off beforehand. In the case the painting surface is made out of wood, it would be a good idea to use primers.

 

  • 2/ Use a combination of brush and roller

 

A short roller is the best tool to paint over large and long surfaces so make sure you have one. When it comes to panting narrow edges and tight corners, a compact paint brush would prove to be exceptionally handy.  With a roller and a brush by your side, you finish painting the interior in a blink of an eye.

 

Do remember to take care of them by washing away all the paint residues on the body of the tool. To leave these tools soaking in paints would make it hard for you to use them in time of need. The paint would freeze them solid after some time and it’s quite a tedious task to unfreeze the tools.

 

  • 3/ Mix a couple of paint can together to keep the color consistent

 

The color of paint could vary slightly from can to can and the difference could be annoying in certain cases. Therefore, grab a big bucket and add in there several cans of paint, it would quickly solve your color problem. You could always pour the leftover paint back into the cans for later usages so just add as you like.

 

The amount of paint to use should be estimated by using a process called boxing which utilizes 5-gallon buckets. For extended paint jobs, it’s often advised that you should use a roller screen instead of the usual roller tray. The roller screen permits the painter to quickly load the roller, and as a result, cut down the painting time.

 

  • 4/ Avoid ugly lap marks by rolling the full height of the wall and maintain a wet edge

 

Lap marks form when you happen to paint over portions of the paint that are already dry for some time. It would leave unsightly stripes on the paint job and that is a common issue with quick dry latex paint. Luckily, there are a couple of simple methods you could apply to prevent the forming of the troublesome lap marks.

 

Keep the roller loaded for the duration of the project, reload it regularly so the roller never gets too dry. Move the roller up and down in the manner that let you completely cover the full height of the wall. To keep a wet edge, each of the strokes must properly overlap the previous ones before the paint could dry.

 

  • 5/ Let the paint dry before you start cutting the painter tape

 

Wait for a day before you attempt to remove the tape, do it early and you may mess up everything. And don’t yank the tape off by force alone, you have to cut it lose first and do it gently. Slice a knife between the tape and the paint as you pull the tape off at a 45-degree angle.

 

  • 6/ Paint the trim before the ceiling and the wall

 

Following a logical order allow you to paint the interior effectively so start with the trim and then everything else. Compared to the ceiling and walls, it’s much easier to paint over the trim and then remove its painter tape. That is why you should finish processing the trim and wait for it dries before moving on to other surfaces.

 

  • 7/ Use cotton cloths as covers

 

No matter how careful you are, you may still accidentally spill or splatter the paint so you better come prepared.

Tape a couple of cotton sheets together and lay them on the floor to set up a convenient nonslip surface. In the case you don’t have cotton cloth on hand, rosin paper would be an excellent alternative for paint cover.

 

  • 8/ Paint along the edge to keep a consistent texture

 

People often paint corners and areas around the trim using a brush which leads to the forming of unique textures. To keep the texture consistent, you have to roll over these spots with a roller before the paint could dry. Handle the roller as careful as possible and don’t let it bump into the opposite paint surface or the trim.

 

  • 9/ Feather out the paint where you are unable to keep a wet edge.

 

When you could not cover the painting surface properly in continuous strokes then it’s best to feather out the paint. That would allow you to efficiently minimize the build-up of excessive paint and lap marks as well.

 

  • 10/Sand between each coat of paint for a smooth finish

 

Should you wish to apply multiple coats of paint then you must remember to sand between the coats. Wait for the paint coat to dry then sand the place with fine-grit sandpapers before applying the next coat.

How To Drill A Hole In Ceramic Tiles Without Damaging Them

Ceramic tile is commonly used on the house wall, floor and alike due to its excellent characteristics as a covering material. However, it’s rather delicate as well, if you handle ceramic improperly then you can end up in a nasty mess. Drilling and cutting ceramic tile are tasks which require a lot of patient in order to achieve the desired result.

Read more

How to Remove Liquid Nails From Wood with Ease

Have a hard time separating that stubborn layer of Liquid Nail adhesive? Check out this article to learn how to remove Liquid Nails from wood on your own.​

More…

Overview

When you want to stick certain things together without using screws or bolts, the adhesive is a really good option. Among the adhesive brands, Liquid Nails provide well – know and effective lines of products. However, it’s may be troublesome to remove it from surfaces such as wood if you made a mistake.

bonding-of-wooden-bars-apply-the-adhesive-to-the-bonding-surfaces

The moment it dries, Liquid Nails adhesive becomes extremely tough to handle if you want to perform any adjustment. That is why knowing how to remove Liquid Nails from wood may come in handy from times to times. Take a look down below to learn the method that can effectively assist you in this type of situation.

Tools and gears that you need to have to perform the process

•A clean piece of cloth soaked in soapy water: Soapy water is the perfect removing solution for latex-based Liquid Nails if it hasn’t cured completely. It’s not enough if the adhesive is already dried though.

•Mineral essence, petroleum jelly or vegetal oil: Removing solutions that work the same as the above but only effective against solvent-based Liquid Nails

•Music wire, wire cutter and handle: You can find this in automobile shops. Its purpose is to slowly grind and saw the adhesive away. Naturally, you will need the wire cutter to cut it into sufficient length. Also get a handle if you afraid of being cut while using the wire.

•Screwdriver and scrapper: To pry and chip the adhesive

•Hairdryer: The machine will help you soften the adhesive and loosen its grip on the attached surface.

•Hot water and dry ice: An excellent way to crack the adhesive with a sudden change in temperature

•Protective gear: Liquid Nails is a dangerous substance if come in contact with your skin so be careful. Make sure that you have a pair of goggles and gloves on whenever you near the liquid.

When you have gathered everything, let’s get to work.

•Step 1: Determine the adhesive nature and heat it up

You can remove the Liquid Nails much easier if you know it’s latex-based or solvent-based. The nature of the substance is right on the adhesive ingredient list. With this information, you will know exactly what to use to efficiently remove the Liquid Nails.

Next, start your hairdryer and focus it toward the middle of the adhesive layer. The ideal temperature to use here should be 140 degrees Fahrenheit or 60 degrees Celsius. Keep doing this for one to two minute to properly heat up the adhesive.

Generally, it will take 7 days for Liquid Nails adhesive to fully bond with attached surfaces. Yet in real life, you may already struggle to remove it in less than an hour. The longer you leave the liquid there, the harder to remove it later so work quickly.

Determine-the-adhesive-nature-and-heat-it-up

•Step 2: Use the hot – cold solution and pour in the removing solutions

If you are uncertain that you can manually remove the adhesive, it’s time for the dry ice and hot water combination. As usual, make sure the glove is on since both of them are not any less dangerous than Liquid Nails. Boil a pot of water and place it on top of the adhesive layer with a towel underneath.

Wait for five minutes then replace the hot water pot with a metal tray or bucket of dry ice. The dramatic jump in temperature should crack the adhesive integrity and ease the removal. Do keep in mind that you must pay utmost attention while you are doing this.

Use-the-hot-or-cold-solution-and-pour-in-the-removing-solutions

Base on the adhesive nature, you can also try to drip several drops of suitable removing solution on the adhesive. Wait for several days for the removing solution to take effect. You can use this method and the above as supplements or alternatives to Step 1.

With a bit of luck, you may have already dislocated the Liquid Nails from the wood. The removing process can be done arguably in the cleanest manner like this. However, should the adhesive remain ignorant, probably the best way to do this is with a bit of force.

•Step 3: Cut out the music wire and start wedging the adhesive

Grab the wire and cut it into a length that 2 or 3 times longer than the width of the Liquid Nails layer. After that, bent the wire around the adhesive edge and hold its ends with both of your hand. In the case that you are using handles, connect the loose ends to them or ensure that you equipped your gloves.

Now you just need to simply wedge the adhesive back and forward till you can completely get rid of it. Remember to apply just enough force slowly and steadily then the Liquid Nails will come out eventually. Continue sawing and grinding till you reach this goal.

As a precaution, every once in a while, stop and use the screwdriver or scraper to pry the gap. This may sometime speed up the process immensely and prevent any possibility of re-adhering. There will be a lot of friction and heat involved with may allow the thermoplastic adhesive to attach itself again.

If you spot any residual adhesive below the layer, promptly scrap them away as well. Apply extra removing solution if needed to make the scrapping easier. Since you are dealing directly with the wood surface, don’t use too much force if you want to preserve it.

Cut-out-the-music-wire-and-start-wedging-the-adhesive

•Step 4: Clean up

When most of the adhesive is out, there should be some traits left. To get them out, soak the piece of cloth in removing solutions again and cleanse all the remaining stains and residuals. At this stage, try not to force your way through since you have a high chance of ruining the wood surface.

If everything goes smoothly, the wood surface shouldn’t have any traces of Liquid Nails left. Now just dispose everything properly and you can proceed to do whatever you desire with the wood.

Conclusion

And that should be the end of the guide, not too hard to follow, right? Liquid Nails is an excellent adhesive for wood and alike but can also be annoying to remove if accidentally apply. But as long as you know how to remove Liquids Nails on wood, the entire ordeal can be solved quickly and effortlessly.

How to Measure Copper Pipe | Useful Tips on Tools Guide

You are about to install new systems or facilities in your house and they will be connected to the house pipes network. But then you realize that in order to get going with the installation, you will need to get an exact measurement of the pipe and you really don’t know how to do it. Well no need to worry, this article will provide you with some simple instructions on how to measure copper pipe entirely on your own.

More…

How to Measure Copper PipeOverviewsThe preparationsThe procedures• The string method• The ruler and tape measure combination• The caliper methodConclusion

Overviews

So you intend to do some major remodel to your house and that includes putting in a new air filter facility, replacing the water supply system or updating the heating unit to the latest model. When it comes to these systems and facilities, every action must take into account the pipe network. And among the considerations, the pipe dimension is very important. If you happen to have a hard time getting a correct measurement of the copper pipe then the information below will be of immense usefulness.

instructions on how to measure copper pipe

Measure the copper pipe is not just on the outside, you must also need to get the inside measurement as well as the proper fitting for them. It’s not easy to get all of the measurements right at first try, especially when you are not a professional plumber. But it’s really not that hard, you can do it by yourself swiftly and easily as long as you get the right tools and suitable procedures. First, let see what you need.

• Note: Nowadays pipes usually come with labels of their dimension. Try to see if you can spot them anywhere on the pipes before you have to resort to getting the measurement on your own.

The preparations

You are not going to need anything too specialized here, just the usual stuff that you can find in your house or improvise on the spot. Basically, you will need a string, a ruler, a caliper and tape measure. They will help to get the exact diameter, length and width of the pipe, both inside and outside. Technically, you can get all the measurement with just one of the tool above but it would be best to measure the pipe several times over and with all the tools so that you can get the pipe exact dimension.

best to measure the pipe

And of course, you will need something to mark on the pipe so you know how to assemble the pipe right. You may also want to get rid of the rust, dust or other foreign material in the exterior and the interior of the pipe to get the proper measurement so sandpaper is necessary. The measuring should be conducted in a clean and dry environment so if your pipe is either too hot or too cold, take it out and wait till the pipe back to normal temperatures. Same can be said about pipes with the presence of water or moisture.

The procedures

• The string method

This is arguably the easiest way to get the diameter of the pipe. Simply wrap the string around the pipe and check the length of the string needed to cover the pipe completely for once. That should give you the circumference of the pipe which is the distance to go around the pipe once. And as stated above, this only work if there is no anything between the string and the pipe surface so ensure that the pipe surface is as smooth as possible and remove the insulation if you see any.

string-method-easiest-way-to-get-the-diameter-of-the-pipe

The downside of this method is you don’t really get the measurement right away. You will need to look for a chart and transform it the proper number that you can actually use. And still, that is just the approximated prediction, this type of measurement can’t offer a precise number. It did narrow down the range of the precise pipe measurement though so it’s good to use it as a reference.

• The ruler and tape measure combination

This method offers better accuracy than the string method and you can actually gather all the necessary measurement right away. The ruler will help you get the pipe outside and inside diameter while the tape measure can act as a more precise version of the string which you may cross check both of the results to determine the correct dimension of the pipe. Do remember to clean out the inside and outside of the pipe to get the most accurate measurement.

ruler-and-tape-measure-combination

 

 

Photo via http://2.bp.blogspot.com

While indeed much more accurate than the string, this combination still not going to give you the best result since the measuring units on the ruler and tape measure usually not small enough to get you the precise measurement. It did give you numbers that are much closer to the desired result than the string though. Use the result you get from this along with the measurement from the string method to deduce out the proper specifications of the pipe.

• The caliper method

This can be said to be the most accurate option of all. With the small and detail measuring unit, you can get pretty much the exact measurement of the pipe. You can both measure the inside and outside diameter of the pipe with it and the results can be said to very precise. If you have this then use it right away from the start. Just clamp the inward hinges to measure the pipe exterior while the outward hinges are for the pipe interior measurement. It’s very easy to use and the numbers it provides are highly reliable.

pretty-much-the-exact-measurement-of-the-pipe

One minor downside of this method happens to be a result from its advantage: Very small measuring units. You may need a magnifying glass to see the correct measurement if you don’t have a good eyesight. To neutralize this, you can buy a digital caliper instead of the dial one so you can see the result easier. However, the digital caliper is more expensive and may not work properly in hot or humid environments so pick the model that suits your conditions the most.

Conclusion

And that would the end of this article, hope that you don’t find it too hard to understand? It’s very problematic to get the precise dimension of the pipe if you don’t know how and sloppy measurements may lead to disastrous results. But from now on, you already got several ways to do it right. By applying the use of tools stated above, measuring the pipe is nothing more than a menial task that you can do by yourself in mere minutes.

Is the article enjoyable? If you feel so then give it a like, share and comment.

How to Remove Silicone From Glass Shower Door | Tips and Tricks on DIY

Looking for a way to get rid of that detestable silicone caulk on the glass door in your shower room without damaging or cracking the screen? Well look no further, you answer is finally here. This article will show you instructions and hints on how to remove silicone from glass shower door by yourself quickly and efficiently.

More…

How to Remove Silicone From Glass Shower DoorWhat do you need to have?How to remove the silicone?Step 1: Inspection.Step 2: Get rid of the easier spotsStep 3: Apply the heat.Step 4: Use the chemicalStep 5: Clean upConclusion

So you just finished remodeling your entire bathroom and put on a brand new glass shower door. But then you notice there are some weird spots littered on the surface of the glass. No matter how hard you wipe, these spots just don’t disappear. Well, you can’t just get them out that easy because they are hardened silicone caulk.

How to Remove Silicone From Glass Shower Door

And since you are dealing with glass material here, use too much force and you may ruin the door. Feeling confused? Then this article got a perfect solution for you. Silicone caulk is commonly used as a sealant on glass objects and alike. But sometimes, the silicone caulk manages to get into contact with the glass window itself and left to harden. After that, it’s very hard to remove since glass is a delicate material. But it’s not too difficult at all. All you need to do is to gather the suitable tools and apply correct techniques below then the silicone spots will disappear for good.

What do you need to have?

You don’t need anything too extreme here, just some normal household appliances will finish the job. Well, so these are what you need to gather: hair dryer, a razor blade (or a scrapper) and a bucket. You can also get a silicon remover spray can in any hardware store as a final solution if everything else is not working. But just to be safe, before you attempt to use any chemical solutions, read the manual and ingredient carefully to decide if they are appropriate to use or not. And don’t ever mix them together.

equip-face-and-hands-protections

It’s also wise to equip face and hands protections since you are dealing with toxic chemical here so goggles, face mask and gloves are a must. And remember to create as much air circulation as possible by opening all windows and doors.

How to remove the silicone?

Step 1: Inspection

Exam the spots, determine their status and mark their locations. This will help you to decide the time and the amount of work you have to do here. Make sure NOT to mark the location where the good caulk is supposed to be. If possible then you should use the razor blade to slice the caulk around the door frames and joint so as to easily identify the excess caulk from the good caulk.

determine-their-status-and-mark-their-locations

Photo via https://i.ytimg.com

Step 2: Get rid of the easier spots

For the most part, silicone caulk can be removed with ease. Use the razor blade, the scrapper or even a combination of both to slowly slide under the caulk and pick them out. Don’t apply too much force at once and instead use just as much force needed and increase it according to the hardness of the silicone spots. Keep repeating the process till every spot are dealt with.

Step 3: Apply the heat

You may eventually run into certain spots that are too tough to pick out by the method above and you fear to damage the glass appearance if you keep trying. This is when forcing the blade no longer work and it’s high time to take out and use the hair dryer. Silicone tends to brittle under constant heat which makes the hair dryer a very useful tool for removing harden silicone. It’s also much safer than to use the chemicals that just may even more harmful to your health than the silicone caulk.

Apply-the-heat

All you need to do is simply focus the hair dryer on the silicone spots for a few minutes and the sport would start cracking. Now just take out the razor blade and do the same as before. But beware, if the excess silicone caulk is located near any plastic component, if you don’t concentrate then you may ruin the plastic integrity with the heat as well. So it’s wise to keep the hair dryer at minimum setting and shield any plastic parts on the door before you do this.

Step 4: Use the chemical

Most if not all of the excess silicone caulk should be gone by now but if there are still some stubborn spots remain then only one solution remain: The silicone remover. There are some noble chemicals on the market for this job, one of them is the WD – 40. But no matter what is the chemical you intend to use, chances are they very harmful if inhale of ingesting by mistake so handle them with care.

Use-the-chemical

As mentioned above, you should determine the suitability of the chemical first before applying them and don’t mix two or more solutions together since it may lead to unpredictable results. A way to test the chemical is to scan the ingredients list or put a small amount of it on the glass and wait to see if there is any negative effect. And be sure to put on full protective gear when you interact and use the chemical. After that, simply apply a suitable amount of chemical on the remaining spots and wipe them out.

Step 5: Clean up

Put all the removed silicone caulk into the bucket and take them to disposal. There should be still some residue and traces of the caulk that have a negative effect on your glass shower door. Luckily, it’s easy to neutralize them. All you need to do is a get a bucket of warm water and put in several teaspoons of liquid soap then soak a rag in. Next is to wipe the entire door clean and rinse the door with warm water against once you done.

get-a-bucket-of-warm-water-and-put-in-several

Conclusion

And that cover pretty much all you need to know, fairly easy to follow, right? It’s a shame to see a recently installed glass shower door littered with excess silicone caulk. But now you no longer have to endure that anymore. By gathering the proper tools and applying suitable techniques that are shown in this article, all those detestable spots will be gone before long. And you can do this easily on your own with out any complicated procedures or expensive gears.

Is the article helpful? If so then please like, share and comment.​

Helpful Tips and Tricks on How to Glue Felt and Wood Together

How to glue felt to wood easily and efficiently along with what you will need to prepare, all by yourself. After you have read this through, you will have no trouble pulling this off on your own at your house

More…

Introduction

So you are working on a wood project and something to protect the wood surfaces from scratches and reduce the frictions is just what you need. So you decide to glue in some felt. But it’s easier said than done and you probably clueless about how to actually do it, right?

Well, then you are in luck. This article will show just how to glue felt to wood without messing up everything.

how-to-glue-felt-to-wood-without-messing-up-everything

As stated above, you are going to need to look for high quality felt if you want your project to be done as smoothly as possible. Like any textured material felt has a tendency to stretch while you are working on it. High quality felt stretch less than lower quality one which makes them easier to handle and manage.

• Felt

Most of this you can find with ease in any hardware store or even just around your house. The most important part is to make sure that they are good quality and in their best conditions. If you can do it then your wood object appearance is guaranteed to be as beautiful yet still durable. Well, then let’s take a look at what you are going to need here.

What do you need to prepare?

Gluing felt to wood is not that hard but you may run into several problems: The felt keep soaking up the glue, the wood surface is too slippery, the felt is too big to fit in tight or small space, etc.

You can avoid many of that simply by following the preparations and instructions below. It’s a step – by – step guide so you should have little trouble to understand and apply it.

And if your wood object is located where it’s would be exposed to sunlight, fading may be an issue. Purchase the felt from well – known brands to be assured of their quality and color.

Next is to decide the felt thickness. Try to determine the correct thickness of the felt base on the angle of the wood project. Sharp and pointy angle should be a bit thicker but not too thick or you will have a hard time gluing the felt in. And the felt shouldn’t be too thin either as it may tears and rips when being grazed upon.

• Glue

Glue-Wood

This depends on the dimension and how easy to access the side of the object where you intend to put on the felt. If the wood object size is big while being surrounded by smaller object or areas, wet cement is a good option.

An adhesive is also nice if you are not afraid of an overspray. And for small scale wood projects, Elmer’s is the brand of glue you need.

• Associated tools

You are going to need foam brushes if you intend to use wet cement or Elmer’s glue. If you have no other use for the brushes after this then just go for cheap one – time – use brushes. But you intend to do more gluing stuff then invest in paint thinner.

For projects that involved adhesive, you will need to lots of newspaper or removable tape to shield areas near your feet. A roller to flat out the wrinkle on the felt is also recommended but if the felt area is small, a credit card or any flat object will do just fine. And finally, a pair of scissor or cutting tools to cut and trim the felt is necessary.

• Safety concerns

Face mask and goggles are advisable when you are gluing the felt to the wood surface so as to protect your eyes and nose from harmful chemicals. It’s would be best to do all of this outdoor but if you have to do this in enclosed space, open all doors and windows to circulate more airs.

How to perform the action?

Step 1: Prepare the felt

In this step, you need to measure the length and height of the space of wood surface you need to cover by felt. Determine the appropriate shape by taking into account all measurements.

If the shape happens to be too difficult, making a template from a piece cardboard is a good idea. Then simply cut out suitable felts and move on.

Step 2: Put in the glue and push the felt in.

Put-in-the-glue-and-push-the-felt-in

Now when you have suitable felts in your hand, you need to start applying the glue on it. The trick to prevent a messy situation here is to apply the glue as you go instead of putting them on at once.

Slowly put the glue on one side of the felt or on the wood surface then gently press them against each other. Keep doing this until the felt cover all the wood surfaces.

If the wood surfaces are too slippery and the felt keep fall off, you can use a double – sided duct tape to act as a connection between the wood surface and the felt.

First, put the tape on along the edges of the object surfaces, remove the tape protection and push the felt in. You still need to apply the glue into the felt since the tapes only act a temporary measure to hold the felt, not a long term way to glue the felt in.

Step 3: Add pressure and wait for it to dry

This is the final step, use a roller or tool of your choice to flatten out all the wrinkles. After that, put a heavy object on or pressed against the felt to keep it as flat as possible.

You may want trim around the felt a better look but after that, it’s mostly done. Now wait for a few hours for the glue to dry and that would be it.

Add-pressure-and-wait-for-it-to-dry

Conclusion

And that concludes the guide, not too hard to follow, right? The felt will ensure the surface of your wood object stay at its best condition as long as the felt is intact. And to do just that, all you ever need is to gather the appropriate materials and apply the procedures mentioned above which are very simple and easy to execute.

At the end of the day, the felt will add a nice touch to your wood object overall appearance and bring out a refreshing atmosphere.

Like the article? Then share it with friends and comment to offer us your opinion.