How To Paint Kitchen Cabinets White Without Sanding

As time goes by, the quality of the house furniture degrades slowly yet steadily and kitchen cabinets are no different. Eventually, if you wish to maintain the aesthetic value of the kitchen interior, you better consider painting the cabinets. But what to do in the case you are unable to sand their surfaces before you can actually start?

In such situations, knowing how to paint kitchen cabinets white without sanding shall come in quite handy.  The color fits well in pretty much all kitchen layouts and makes the room look rather fresh. If you intend to do that but clueless about what to do, you will find everything you need below.

The required material and tool for the job

Most of the supplies you need to have can be found around the house or in the local hardware store. Namely, you must obtain cleaning product, paint primer, deglosser, brush and roller. It’s a good idea to use this chance to process the cabinets hinges so grab metal finish paint as well.

closeup-person-holding-paint-brush-painting

To speed up the painting process, you should remove the cabinets from their mountings and disassemble them into components. Therefore, prepare a screwdriver nearby to loosen the cabinets screws and hinges. If you want to do the painting indoor, buy some rosin paper to prevent the spilling of the chemical.

mask-gloves-goggles-pile-isolated-on

Since you are about to deal with lots of chemicals, you need to put on protective gears on until the end. Wear a pair of gloves, goggles and facemask when you are handling the painting material to be on the safe side. When you got all the necessary material and tool then it’s time to get work.

The painting procedures  

  • Step 1: Remove the cabinets and split them into parts

Locate the cabinets screws, unscrew them and gently detach the components. Old hardware screws might be hard to handle given the age so add some lubricant if needed to aid you. When the cabinets are fully disassembled, carry the parts to a place with enough room to perform the painting there.

Remove the cabinets and split them into parts

Remove the cabinets and split them into parts

Spread a couple rolls of rosin paper over the floor and lay the cabinets components on them. Remember to group the screws together so you don’t lose them by mistake, mark the hinges positions as well. It will be quite useful when you have to reassemble the pieces which without marking may make you feel confused.

With the parts nicely arranged on the paper, you have to cleanse them carefully and thoroughly with the cleaning product. The idea is to get rid of all foreign materials that could hamper the painting process or lessen its effectiveness. Pay special attention to the cabinets surfaces such as its door and frame.

  • Step 2: Scrub the cabinets with the deglosser.

Deglosser is a type of chemical which is commonly used to process a particular area for a fresh coat layer. Its effect is more or less similar to the sanding of the target surface with sandpaper. They all help remove old paint, gloss, varnish and alike so the place can fully accept a new paint job.

Scrub the cabinets with the deglosser

Again, this is not an exactly safe chemical to play around so handle it with the utmost concentration. Rinse a towel in a moderate amount of deglosser then started scrubbing the cabinets parts with your gloves on. Move your hand in a circular motion to equally spread the deglosser across the components surface.

While effective, the application of the deglosser must take place in the outdoor or a ventilated room for safety reason.  When you finish the scrubbing, leave the deglosser to dry for a couple of hours before moving on. If you have done it correctly, the cabinets shall be lightened by the deglosser by the time they are dried.

  • Step 3: Prime the cabinets

Priming is an essential step if you want a strong bond between the paint and the surface. As the deglosser dried off, the next thing to do here is to use the brush to apply the primer. To ensure a nice and smooth surface, try to get the primer in as fast as possible while it’s still wet.

With the primer layer in place, roll over it several times with a dry foam roller to even the strokes. Repeat the process till all the cabinets surfaces you intend to pain are well applied with primer. Should everything goes smoothly, the primer layer will have no trouble adhering itself tightly to the already existing deglosser.

  • Step 4: Paint the cabinets

At this point, the only thing left to do here is to simply paint cabinets in whatever way you want. Thanks to the primer, the paint shall have a much easier time bonding with the surfaces of the cabinets. It’s advised to pain two layers of paint with time to dry in between to achieve maximum effectiveness.

Give the paint a day to dry before you attempt to put everything back together again. Leave the cabinets parts where there are lots of air circulations to dry the paint and remove the chemical smell. With the right level of ventilation, the paint should dry fairly quickly so be patient and wait till it’s done.

  • Step 5: Reassemble

Base on the markings that you have done from before, reassemble the cabinets pieces back to their original configurations. Take this time to spray the hinges with metal finish paint and give them a new look as well.  When the parts have become a single unit once more, the project is now complete.

classic-kitchen-green-interior-paint-hardwood

Gather used material and supplier for proper disposal with special attention to the chemicals. Deglosser, paint and paint primer are dedicating products which require suitable handling and storage.

Conclusion

And that is how to paint kitchen cabinets white without sanding, pretty easy for you to follow, right? You may feel that it’s a bit tricky to perform at first but painting without sanding is not exceptionally complicated.   Simply follow the instruction above and move forward at your own pace then you will finish it in no time.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: