How to Remove Liquid Nails From Wood with Ease

Have a hard time separating that stubborn layer of Liquid Nail adhesive? Check out this article to learn how to remove Liquid Nails from wood on your own.​



When you want to stick certain things together without using screws or bolts, the adhesive is a really good option. Among the adhesive brands, Liquid Nails provide well – know and effective lines of products. However, it’s may be troublesome to remove it from surfaces such as wood if you made a mistake.


The moment it dries, Liquid Nails adhesive becomes extremely tough to handle if you want to perform any adjustment. That is why knowing how to remove Liquid Nails from wood may come in handy from times to times. Take a look down below to learn the method that can effectively assist you in this type of situation.

Tools and gears that you need to have to perform the process

•A clean piece of cloth soaked in soapy water: Soapy water is the perfect removing solution for latex-based Liquid Nails if it hasn’t cured completely. It’s not enough if the adhesive is already dried though.

•Mineral essence, petroleum jelly or vegetal oil: Removing solutions that work the same as the above but only effective against solvent-based Liquid Nails

•Music wire, wire cutter and handle: You can find this in automobile shops. Its purpose is to slowly grind and saw the adhesive away. Naturally, you will need the wire cutter to cut it into sufficient length. Also get a handle if you afraid of being cut while using the wire.

•Screwdriver and scrapper: To pry and chip the adhesive

•Hairdryer: The machine will help you soften the adhesive and loosen its grip on the attached surface.

•Hot water and dry ice: An excellent way to crack the adhesive with a sudden change in temperature

•Protective gear: Liquid Nails is a dangerous substance if come in contact with your skin so be careful. Make sure that you have a pair of goggles and gloves on whenever you near the liquid.

When you have gathered everything, let’s get to work.

•Step 1: Determine the adhesive nature and heat it up

You can remove the Liquid Nails much easier if you know it’s latex-based or solvent-based. The nature of the substance is right on the adhesive ingredient list. With this information, you will know exactly what to use to efficiently remove the Liquid Nails.

Next, start your hairdryer and focus it toward the middle of the adhesive layer. The ideal temperature to use here should be 140 degrees Fahrenheit or 60 degrees Celsius. Keep doing this for one to two minute to properly heat up the adhesive.

Generally, it will take 7 days for Liquid Nails adhesive to fully bond with attached surfaces. Yet in real life, you may already struggle to remove it in less than an hour. The longer you leave the liquid there, the harder to remove it later so work quickly.


•Step 2: Use the hot – cold solution and pour in the removing solutions

If you are uncertain that you can manually remove the adhesive, it’s time for the dry ice and hot water combination. As usual, make sure the glove is on since both of them are not any less dangerous than Liquid Nails. Boil a pot of water and place it on top of the adhesive layer with a towel underneath.

Wait for five minutes then replace the hot water pot with a metal tray or bucket of dry ice. The dramatic jump in temperature should crack the adhesive integrity and ease the removal. Do keep in mind that you must pay utmost attention while you are doing this.


Base on the adhesive nature, you can also try to drip several drops of suitable removing solution on the adhesive. Wait for several days for the removing solution to take effect. You can use this method and the above as supplements or alternatives to Step 1.

With a bit of luck, you may have already dislocated the Liquid Nails from the wood. The removing process can be done arguably in the cleanest manner like this. However, should the adhesive remain ignorant, probably the best way to do this is with a bit of force.

•Step 3: Cut out the music wire and start wedging the adhesive

Grab the wire and cut it into a length that 2 or 3 times longer than the width of the Liquid Nails layer. After that, bent the wire around the adhesive edge and hold its ends with both of your hand. In the case that you are using handles, connect the loose ends to them or ensure that you equipped your gloves.

Now you just need to simply wedge the adhesive back and forward till you can completely get rid of it. Remember to apply just enough force slowly and steadily then the Liquid Nails will come out eventually. Continue sawing and grinding till you reach this goal.

As a precaution, every once in a while, stop and use the screwdriver or scraper to pry the gap. This may sometime speed up the process immensely and prevent any possibility of re-adhering. There will be a lot of friction and heat involved with may allow the thermoplastic adhesive to attach itself again.

If you spot any residual adhesive below the layer, promptly scrap them away as well. Apply extra removing solution if needed to make the scrapping easier. Since you are dealing directly with the wood surface, don’t use too much force if you want to preserve it.


•Step 4: Clean up

When most of the adhesive is out, there should be some traits left. To get them out, soak the piece of cloth in removing solutions again and cleanse all the remaining stains and residuals. At this stage, try not to force your way through since you have a high chance of ruining the wood surface.

If everything goes smoothly, the wood surface shouldn’t have any traces of Liquid Nails left. Now just dispose everything properly and you can proceed to do whatever you desire with the wood.


And that should be the end of the guide, not too hard to follow, right? Liquid Nails is an excellent adhesive for wood and alike but can also be annoying to remove if accidentally apply. But as long as you know how to remove Liquids Nails on wood, the entire ordeal can be solved quickly and effortlessly.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: