Pro Tips on How to Remove Window Screen Without Tabs

Struggling to get your window screen out of the frame since it doesn’t have the usual tabs? Well you can learn how to remove window screen without tabs by yourself, here and now. With easy to find tools and simple techniques, the removal of window screen can’t be any easier from now on.

More...

Introduction

So your window screen is a bit dirty and you want to remove it for cleaning. Or it got some scratches on and you need to put in a replacement. Either way, you need to remove the screen from the frame. But then you run into a problem: The window screen doesn’t possess the usual tabs to pull it out. Then you struggle for hours and still can’t get the screen out. Well struggle no more, this article will provide you a guide on how to remove window screen without tabs.

window screen is a bit dirty

There are many types of mechanisms installed on a window for screen removal. And the tabs mechanism is arguably the most common way to get the screen out of the frame since it’s easy to execute and require almost no tool at all. But there are still screens that utilize different removal methods other than tabs. Your screen probably falls into this category and it may require appropriate tools. But you don’t have to worry, below is a simple step – by – step instructions about how to specifically deal with this situation.

What tools do you need?

There are two additional ways to remove a window screen from its frame beside tabs, they are “The pins” and “The pry”. For “The pins”, it also requires no tool and the way to get the screen out is only a bit different from the usual tabs. And there is “The pry”, now this is a bit tricky since you have to use certain tools to pry the screen up so it can be taken out of the frame. In this case, an ill – suited tool or incorrect techniques will probably result in a bent screen or damaged screen. But as long as you follow the instruction closely, you have nothing to worry.

• Prying tools

Prying-tools

You can get these tools from your local hardware store or they are already in your house. You can use the paint can opener, flat – headed screwdriver, putty knife or alike. The point here is to get a durable tool that you can use as a leverage to pry the screen off the frame. But you need to beware not to use tools with sharp angles to press against either the screen or the frames if you want to preserve their appearances.

• Lubricants

If the window screen proved to be too hard to operate, chances are dust, rust or foreign materials have been accumulated hence demand the use of lubricants. Nothing too fancy, some cooking oil from the kitchen or any slippery liquid at all will do just fine.

• Safety precaution

Safety-precaution

When you remove the screen from the frame, whatever accumulated in between will fall out and may be harmful to your health. These may even scratch your hands in the removal as well. So it’s wise to put on a face mask, a pair of goggles and gloves just to be on the safe side.

How to do this?

Let’s separate the process into “The pins” and “The pry” so that you can apply whatever way suitable to your situation.

• The pins

Step 1: Locate the pins on the screen.

Check the window screen bottom corners. If you don’t see any tabs yet there are some kinds of spring loaded locking devices there then this is the screen that uses the pins mechanism. It should be located on the interior side of the window for easy removal and prevent access from the outside.

Step 2: Operate the pins

Grab the pins at the same time – one with each hand – and pull them straight back. Keep in mind that the pins tension mechanism may prove to be a bit hard to handle after a long time so if you can make it move on your own, hit it gently with a screwdriver or a hammer to get it to work.

Step 3: Take out the screen.

After you pulled the pins, the screen should be unlatched from the bottom frame now so gently pull the screen toward you until it’s an inch away from the bottom frame. Remember to use just use only as much force as required here. Then swiftly slide the screen away from the opposite frame and the screen should be firmly in your hand now, you can do anything as you see fit.

• The pry

Step 1: Pick a good spot as leverage

In this type of window, there is nothing to do but pry, pry and pry. Therefore, it’s good to use an appropriate tool on a suitable spot so that you can unlatch the screen from the frame by your force. A good place to start is the bottom frame. You can choose either the center point or the edges, whichever seem to be more suitable as a leverage location.

Step 2: Start prying.

After you have picked a spot, use tools stated above such as a screwdriver, putty knife and alike to slip in the spot. Now slowly and steadily apply force in an up – and – backward fashion to get the screen to unlatch and fall toward you. Also one thing, use lubricant if you like so that the whole process will be easier and don’t cause substantial damage to your window frames.

After a while, the screen should be out of the bottom frame and now you can remove it from the upper frame by a simple slide. And that is it, you can do whatever you want with the screen now.​

Conclusion

And that is the end of this article, not too difficult to follow, right It’s indeed problematic that your window screen adopts a not so common method for a removal but simply by following closely the instruction above, it’s no big deal at all. With some simple gears and techniques, you don’t have to struggle every time you want to get the screen out of the frame anymore.

Is this article helpful? If so, like, share and comment to give us your thoughts.​

Click Here to Leave a Comment Below 0 comments

Leave a Reply: